|
Thanks Mark ,but still couldnt get thro'
this is what i did
[root@localhost Desktop]# bzcat ttylinux-xen.bz2 >ttylinux
[root@localhost Desktop]# rm -rf /tftpboot/
[root@localhost Desktop]# cp ttylinux tftpboot/
My stripped conf file looks like this:
kernel = "/boot/vmlinuz-2.6.11-1.1369_FC4xenU"
memory = 64
name = "ttylinux1"
nics = 1
ip = "1.2.3.4"
disk = ['file:/tftpboot/ttylinux,sda1,w']
root = "/dev/sda1 ro"
I dont have a /dev/sda1 partition in my harddisk (the only partition which is is a root partition is /dev/hda6 which holds the FC4 install I am using as dom0 , am i being dumb in not understanding that the root fs has to be a real partition having all the files or /dev/sda1 will do ???..please explain the difference between disk and root..
when i say:
[root@localhost ~]# xm create ttyconf1 -c
Using config file "/etc/xen/ttyconf1".
Started domain ttylinux1, console on port 9616
************ REMOTE CONSOLE: CTRL-] TO QUIT ********
Linux version 2.6.11-1.1369_FC4xenU (bhcompile@xxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.0.0 20050525 (Red Hat 4.0.0-9)) #1 SMP Thu Jun 2 23:33:51 EDT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000004000000 (usable)
64MB LOWMEM available.
Using x86 segment limits to approximate NX protection
DMI not present.
IRQ lockup detection disabled
Allocating PCI resources starting at 04000000 (gap: 04000000:fc000000)
Built 1 zonelists
Kernel command line: ip=1.2.3.4:1.2.3.4::::eth0:off root=/dev/sda1 ro
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Xen reported: 2258.351 MHz processor.
Using tsc for high-res timesource
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 60800k/65536k available (1785k kernel code, 4648k reserved, 506k data, 156k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... disabled
CPU0: Intel(R) Pentium(R) 4 CPU 2.26GHz stepping 07
per-CPU timeslice cutoff: 1462.80 usecs.
task migration cache decay timeout: 2 msecs.
SMP motherboard not detected.
smpboot_clear_io_apic_irqs
Brought up 1 CPUs
softlockup thread 0 started up.
NET: Registered protocol family 16
xen_mem: Initialising balloon driver.
Grant table initialized
audit: initializing netlink socket (disabled)
audit(1123595064.572:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 42BD35A990375F72
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Xen virtual console successfully installed as tty1
Event-channel device installed.
Blkif frontend is using grant tables.
xen_blk: Initialising virtual block device driver
xen_net: Initialising virtual ethernet driver.
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 256 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 156k freed
Inconsistency detected by ld.so: rtld.c: 1180: dl_main: Assertion `(void *) ph->p_vaddr == _rtld_local._dl_sysinfo_dso
PERHAPS I AM AGAIN MAKING A MISTAKE
thanks and regards
Digz
======================================================================================
> > I am trying to run a simple ttylinux as a domU
> > ( from sf.net/xen )
>
> OK.
>
> > /etc/xen/ttyconf looks like what the Xen 2.0 documentation
> > suggests
> >
> > kernel = "/boot/vmlinuz-2.6.11-1.1369_FC4xenU"
> > memory = 64
> > name = "ttylinux"
> > nics=1ip="1.2.3.4"
> > disk=['file:/tftpboot,sda1,w'] .................#the Xen doc
> > says /path/to/ttylinux/rootfs
> > root="/dev/sda1 ro"
> >
> > [root@localhost tftpboot]# xm create ttyconf1 -c vmid=2
> > Using config file "/etc/xen/ttyconf1".
> > Error: Error creating domain: vbd: Segment not found:
> > uname=file:/tftpboot
> >
> > i untarred the ttylinux.bz2 in the empty tftpboot directory (not
> > for any particular reason)
> > [root@localhost ~]# ls /tftpboot
> > bin dev etc init lib linux-install loopfs proc sbin sys
> > sysroot ttylinux
>
> Are you sure the tftpboot directory was empty? ttylinux.bz2 is not a tar
> file, just a compressed file - all it should have left behind it the file
> "ttylinux". I don't know where the other directories came from :-)
>
> The file: directive needs to point to the disk file itself, not to a
> directory. Could you please try:
> disk=['file:/tftpboot/ttylinux,sda1,w']
>
> Let us know how you get on!
>
> Cheers,
> Mark
>
> > what is that i need to change ..the domU is from an FC4 Rpm and
> > i have not been able to run from a physical device as root fs
> > either ,the kernel starts booting and stops at freeing unused
> > memory..156K..which from the FAQ i saw was related to initrd
> > could not fix it that way.....so just waiting for help
> >
> > Digz
> >
> >
> >
> > **************** CAUTION - Disclaimer *****************
> > This e-mail contains PRIVILEGED AND CONFIDENTIAL INFORMATION intended
> > solely for the use of the addressee(s). If you are not the intended
> > recipient, please notify the sender by e-mail and delete the original
> > message. Further, you are not to copy, disclose, or distribute this
> > e-mail or its contents to any other person and any such actions are
> > unlawful. This e-mail may contain viruses. Infosys has taken every
> > reasonable precaution to minimize this risk, but is not liable for any
> > damage you may sustain as a result of any virus in this e-mail. You
> > should carry out your own virus checks before opening the e-mail or
> > attachment. Infosys reserves the right to monitor and review the content
> > of all messages sent to or from this e-mail address. Messages sent to or
> > from this e-mail address may be stored on the Infosys e-mail system.
> > ***INFOSYS******** End of Disclaimer ********INFOSYS***
| 
