[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] domU startup freezes at "Starting plymouth"

On 07/02/2011 03:12 PM, Fajar A. Nugraha wrote:
On Sun, Jul 3, 2011 at 2:25 AM, Mike Wright<mike.wright@xxxxxxxxxxxxxx>  wrote:
Hi all,

I've got xen-4.1.1 running with linux-3.0.0-rc5 and am trying to start my
first guest, f14-x86_64, which does boot on bare metal.

... and here's the first mistake. I assume you're converting an
existing linux installation to Xen?
I highly suggest NOT to do so on your first domU/guest.

The configs below show kernel, ramdisk, and disk assignments for the virtual
machine.  They also show that the virtual machine uses the target disk
devices.  The last section shows part of the boot sequence starting with the
disk assignments, which are successful.  Everything stops at the last line
until some time later when the messages "Boot has failed, sleeping forever"
appears.  (I think this is about where the initramfs hands off control to
the kernel.)

dom0: /etc/xen/vm1

kernel = "/boot/vmlinuz-3.0.0-rc5"
ramdisk = "/boot/initramfs-3.0.0-rc5.img"

This is the first mistake.

While domU can use kernel located in dom0, if you choose to do so then
you also need to specify the additional kernel arguments needed (e.g.
"root=/dev/xvda1"). It should be on an "extra" line.

Also, you need to have a matching set of modules in domU's
/lib/modules (although this does not directly related to the error
you're having now).

disk = [ 'phy:/dev/OneTB/f14_64,     sda1,w',
         'phy:/dev/OneTB/f14_64_swap,sda2,w' ]

this one should be xvda instead of sda

[    0.171095] blkfront: xvde1: flush diskcache: enabled
[    0.172102] blkfront: xvde2: flush diskcache: enabled

... and you need to match "root=..." kernel arg to whatever's detected
here. Since you use sda on the config file, F14's kernel will actually
detect the disk as xvde, which can be confusing. Better stick with

If I can get just one vm running I'll be on my way...  I've been stuck here
since yesterday.  Any help appreciated.

The best way for beginners is start with the easy things first.
Install virt-manager, install a new domU, look at the generated config
file and disk image, then start changing things from there.

Thanks for your help Fajar.

I think you may be being a bit alarmist ;) All I was missing was the root = (or extra =) option (my fault for not reading all the way to the bottom) and that sda1 and sda2 have been superceded by xvda1 and xvda2.

Here are the basics from my vm1 config file:
(boots the virtual machine w/o networking)

kernel = "/boot/vmlinuz-3.0.0-rc5"
ramdisk = "/boot/initramfs-3.0.0-rc5.img"

# vif = ['']

disk = [ 'phy:/dev/OneTB/f14_64,      xvda1, w',
         'phy:/dev/OneTB/f14_64_swap, xvda2, w' ]

root = 'root=/dev/xvda1 ro'

Here are the required changes to the virtual to boot:

Mount the virtual's root partition and make these changes:

  /dev/xvda1 /     ext4 defaults 1 1
  /dev/xvda2 /swap swap defaults 0 0
  #comment out /boot

make sure /lib/modules has matching modules (in my case "3.0.0-rc5").

Now to figure out networking...

Mike Wright

Xen-users mailing list



Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.