[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-users] XCP



Hi Scott,
Thank you for your response.  The three machines I referred to are all on 
static IPs. They are on in the customer's premises running on an ADSL 
connection  - not in a data centre.  Much of my development work, however, is 
done at home.  My ISP only provides dynamic IPs.  I would move to a different 
ISP to get a static IP or group of IPs if it weren't for the fact that I cannot 
get a big fat 50 mbps downstream and a 5 mbps upstream any other way!  Static 
IPs do not give a problem so it's a minor point really.  I'm just interested to 
know why I can't get the gateway address via dhcp.  That's all.
Many thanks,
Frank.

-----Original Message-----
From: Scott Damron [mailto:sdamron@xxxxxxxxx] 
Sent: 23 December 2011 19:01
To: Frank Salter
Cc: xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] XCP

Don't take this the wrong way - but - WHY would you use DHCP for a
VoIP or other server?  Are you running these on site for a customer,
or are they in a data center?  The issues with running any kind of
server via DHCP are beyond the scope of this group I believe.  There
may be a few folks who can provide you with some ideas, but over all,
I would say you are on your own.

On Fri, Dec 23, 2011 at 12:51 PM,  <frank@xxxxxxxxxxxxxxx> wrote:
> Hi,
>
> I have deployed three machines in recent months all of which are loaded with
> XCP 1.0.  These machines are functioning very well in real commercial
> environments.  I intend to deploy further machines in 2012.  All of these
> systems are running MS SBS2011 in a VM and also Trixbox Asterisk based voip
> telephony in another VM.  I am getting fed up,  however,  with
> inconsistencies from commercial ADSL routers which screw up voip and which
> do not provide QoS which is good enough so I have decided to use ADSL
> Ethernet modems instead and perform all routing, firewall and QoS functions
> inside the XCP box.  To that end I have set up an experimental XCP 1.0 box
> with 2 NICS and I have set up iptables on the host machine to perform NAT
> (masquerade) forwarding the entire internet (DMZ) onto the public side of a
> zeroshell VM (firewall) which will allow an easy way to open and close ports
> and which also performs excellent QoS.  The reason why I want to perform a
> NAT masquerade on the host itself is so I can get locked down SSH access to
> the host itself so that in an emergency I can start and stop VMs or even
> reboot if necessary.
>
> All this I have successfully implemented and it all works well.  The only
> fly in the ointment is if the box is connected to an ISP which only provides
> a dynamic IP address.  I have used xe pif-reconfigure-ip to set the external
> interface to dhcp and it does indeed lease an IP address from the ISP.  What
> it does not do however, is to get the gateway address from the ISP.  If I
> connect other boxes (linux or windows) to the internet connection they all
> get a gateway address - but not XCP.  Because I am able to work out what the
> gateway address is I have added it manually at the cli using the route
> command and  internet access then works  - but this is not a solution - only
> a workaround - and if the IP address changed the box would be on the wrong
> gateway.  It would be really great if someone could shed some light on what
> is going on.
>
> BTW.  I have not defined a gateway on the management interface so there is
> only one gateway on the machine.
>
> Kind regards,
>
> Frank.
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.