[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Xen-devel] pci-passthrough and shared interrupts
- To: Konrad Rzeszutek Wilk <konrad.wilk@xxxxxxxxxx>, Pasi Kärkkäinen <pasik@xxxxxx>
- From: Ritu kaur <ritu.kaur.us@xxxxxxxxx>
- Date: Sun, 3 Oct 2010 09:41:55 -0700
- Cc: xen-devel@xxxxxxxxxxxxxxxxxxx
- Delivery-date: Sun, 03 Oct 2010 09:43:03 -0700
- Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=mime-version:in-reply-to:references:date:message-id:subject:from:to :cc:content-type; b=FpcIys8IfqUZ6XzI5NHh9HCZ64sU9ynqodhEQvSoELcaUwmanEcNQ72seleDmeTAO7 /HrCZi1U13BLu4/hqY6Wg02EZCWHQswpT0+IoZHp/8T1aulII/jT0DHAFl8bHGCheeRh qFDOOubg/tyRmqaXArRtl1qT1+NAYDm2zc2ww=
- List-id: Xen developer discussion <xen-devel.lists.xensource.com>
Pasi,
Installation/compilation of xen source on fedora core went through fine. I am facing an issue when dom0_mem is set to 1024M. During boot I get the message
/*********************
Panic on CPU 0
Not enough RAM for domain 0 allocation
**********************/
Same thing happens when dom0_mem is set to 512M
when dom0_mem is set to 256M, I get following message
/***************************
Panic on CPU 0
Domain 0 allocation is too small for kernel image
****************************/
Is 8GB ram mandatory? In my machine it is 2GB ram, inputs appreciated.
Thanks
On Sun, Oct 3, 2010 at 9:07 AM, Ritu kaur <ritu.kaur.us@gmail.com> wrote:
Thanks Konrad, I checked my old emails(back in March 2010) to see if I had tried this combination when I was testing xcp. I did try this combination and the problem I had faced was configuration errors due to IDE_DISK. I couldn't get past this problem. Snippets below
/*********************************************************
Thanks Konrad.
>
> I downloaded new code and still doesn't work(albeit different problem). I
> will enumerate them below
>
> (Please note 1, 2 and 3 are seen with old xen/next as well). What seemed
> simple testing of pci passthrough via config changes doesn't seem to be
> the case.
>
> 1. mkinitrd doesn't work in xcp ddk. I get below errors
>
> mkinitrd -f ./initrd-2.6.32.ing 2.6.32
> modinfo: could not find module ide-disk
> No module ide-disk found for kernel 2.6.32, aborting.
>
******************************************************************************************************************/
On Fri, Oct 1, 2010 at 8:58 AM, Konrad Rzeszutek Wilk <konrad.wilk@xxxxxxxxxx> wrote:
On Fri, Oct 01, 2010 at 08:36:03AM -0700, Ritu kaur wrote:
> Hi Konrad,
>
> Frankly, I am confused. XCP(which is similar to Citrix Xenserver but
> open-source and newer-kernel) requires DDK to build a kernel image. If I
> understand your suggestion correctly I should be able to
>
> 1. Take PVOPS kernel code, compile it in XCP DDK and load it into dom0
> 2. Take PVOPS kernel code, compile it in domU OS and load it into domU
>
> then, I should be able to get pci-passthrough + shared interrupts between
> devices working correctly? Please clarify/confirm
Yes.
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel
|
