[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Xen-devel] pci-passthrough and shared interrupts



On Sun, Oct 03, 2010 at 09:41:55AM -0700, Ritu kaur wrote:
>    Pasi,
> 
>    Installation/compilation of xen source on fedora core went through fine. I
>    am facing an issue when dom0_mem is set to 1024M. During boot I get the
>    message
> 
>    /*********************
>    Panic on CPU 0
>    Not enough RAM for domain 0 allocation
>    **********************/
> 
>    Same thing happens when dom0_mem is set to 512M
> 
>    when dom0_mem is set to 256M,  I get following message
> 
>    /***************************
>    Panic on CPU 0
>    Domain 0 allocation is too small for kernel image
>    ****************************/
> 
>    Is 8GB ram mandatory? In my machine it is 2GB ram, inputs appreciated.
> 

It sounds like you wrote the value wrong, ie. you didn't specify 'M' to make it 
megabytes,
so you got kilobytes.. and thus it's too small to fit the dom0 kernel image 
there.

-- Pasi

>    Thanks
> 
>    On Sun, Oct 3, 2010 at 9:07 AM, Ritu kaur <[1]ritu.kaur.us@[2]gmail.com>
>    wrote:
> 
>      Thanks Konrad, I checked my old emails(back in March 2010) to see if I
>      had tried this combination when I was testing xcp. I did try this
>      combination and the problem I had faced was configuration errors due to
>      IDE_DISK. I couldn't get past this problem. Snippets below
> 
>      /*********************************************************
>      Thanks Konrad.
>      >
>      >    I downloaded new code and still doesn't work(albeit different
>      problem). I
>      >    will enumerate them below
>      >
>      >    (Please note 1, 2 and 3 are seen with old xen/next as well). What
>      seemed
>      >    simple testing of pci passthrough via config changes doesn't seem
>      to be
>      >    the case.
>      >
>      >    1. mkinitrd doesn't work in xcp ddk. I get below errors
>      >
>      >    mkinitrd -f ./initrd-2.6.32.ing 2.6.32
>      >    modinfo: could not find module ide-disk
>      >    No module ide-disk found for kernel 2.6.32, aborting.
>      >
>      
> ******************************************************************************************************************/
> 
>      On Fri, Oct 1, 2010 at 8:58 AM, Konrad Rzeszutek Wilk
>      <[3]konrad.wilk@xxxxxxxxxx> wrote:
> 
>        On Fri, Oct 01, 2010 at 08:36:03AM -0700, Ritu kaur wrote:
>        > Hi Konrad,
>        >
>        > Frankly, I am confused. XCP(which is similar to Citrix Xenserver but
>        > open-source and newer-kernel) requires DDK to build a kernel image.
>        If I
>        > understand your suggestion correctly I should be able to
>        >
>        > 1. Take PVOPS kernel code, compile it in XCP DDK and load it into
>        dom0
>        > 2. Take PVOPS kernel code, compile it in domU OS and load it into
>        domU
>        >
>        > then, I should be able to get pci-passthrough + shared interrupts
>        between
>        > devices working correctly?  Please clarify/confirm
> 
>        Yes.
> 
> References
> 
>    Visible links
>    1. http://ritu.kaur.us/
>    2. http://gmail.com/
>    3. mailto:konrad.wilk@xxxxxxxxxx

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel


 


Rackspace

Lists.xenproject.org is hosted with RackSpace, monitoring our
servers 24x7x365 and backed by RackSpace's Fanatical Support®.