Xen project Mailing List

Re: [Xen-users] e1000e not working with latest linux-2.6.18-xen.hg

To: "Janusz Ulanowski" <janul666@xxxxxxxxx>

From: "Balaji Rao R" <balajirrao@xxxxxxxxx>

Date: Sat, 24 May 2008 13:02:17 +0530

Cc: Amit Shah <amit@xxxxxxxxxxxx>, xen-users@xxxxxxxxxxxxxxxxxxx

Delivery-date: Sat, 24 May 2008 00:32:51 -0700

Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=message-id:date:from:to:subject:cc:in-reply-to:mime-version:content-type:content-transfer-encoding:content-disposition:references; b=OmMTcc/R4+dhehPIZU+7ZhE2Fozh59uDXDXI/l7PkwNlU9Itw7Q/MXXNFcePrbiiZouWWFMeznk6AV+jhcX8fjgWcHQFmS3sdghE0EFPb9sssIMpEV8S6WMaI2I4RJqIiSXxlAOGQRf3hdLQQ3pnFyjVX4MoRAkvO/N5zVKQOEE=

List-id: Xen user discussion <xen-users.lists.xensource.com>

On Fri, May 23, 2008 at 1:59 AM, Janusz Ulanowski <janul666@xxxxxxxxx> wrote: > Balaji Rao wrote: >> >> Hello all, >> >> My e1000e card does not work with linux-2.6.18-xen.hg. The lspci -x output >> from a working 2.6.25-14 f9 kernel is, >> >> 00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network >> Connection (rev 02) >> 00: 86 80 4c 29 07 00 10 00 02 00 00 02 00 00 00 00 >> 10: 00 00 38 e0 00 40 3a e0 e1 20 00 00 00 00 00 00 >> 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 01 00 >> 30: 00 00 00 00 c8 00 00 00 00 00 00 00 09 01 00 00 >> >> >> lspci -vvv says, >> >> 00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network >> Connection (rev 02) >> Subsystem: Intel Corporation Unknown device 0001 >> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- >> Stepping- SERR- FastB2B- DisINTx- >> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- >> <TAbort- <MAbort- >SERR- <PERR- INTx- >> Latency: 0 >> Interrupt: pin A routed to IRQ 20 >> Region 0: Memory at e0380000 (32-bit, non-prefetchable) [size=128K] >> Region 1: Memory at e03a4000 (32-bit, non-prefetchable) [size=4K] >> Region 2: I/O ports at 20e0 [size=32] >> Capabilities: [c8] Power Management version 2 >> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA >> PME(D0+,D1-,D2-,D3hot+,D3cold+) >> Status: D0 PME-Enable- DSel=0 DScale=1 PME- >> Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ >> Queue=0/0 Enable- >> Address: 0000000000000000 Data: 0000 >> Capabilities: [e0] Vendor Specific Information <?> >> Kernel driver in use: e1000e >> Kernel modules: e1000e >> >> Are there any floating patches to help me fix this ? Please help. >> >> Thank you. >> > > I have, > I have Intel Corporation 82575GB Gigabit Network Connection > and I had to download modules from intel site and module is called igb > Maybe it helps. Yea, thank you. I downloaded the e1000e driver from sourceforge and compiled it for 2.6.18. It worked out of the box. Thank you! -- warm regards Balaji Rao _______________________________________________ Xen-users mailing list Xen-users@xxxxxxxxxxxxxxxxxxx http://lists.xensource.com/xen-users

©2013 Xen Project, A Linux Foundation Collaborative Project. All Rights Reserved.
Linux Foundation is a registered trademark of The Linux Foundation.
Xen Project is a trademark of The Linux Foundation.