Re: Two redundant Xen servers with one SAN

[GD <g.d.monnezza@xxxxxxxxxx>]

    "I should have been more precise, I am
    looking into building a active/passive dual node Xen installation
    "
      
      In this case, you can configure a simple but robust architecture
      I'm already running:
      Two Xen Server, storing VMs in LV built on top of DRBD. It's up to
      you if create a DRBD-LV pair for each VM (as I did in my setup) or
      a single DRBD-LVG
      Both Xen host are running, but VMs are running on the host having
      the DRBD(s) active. Xen hosts shares VM conf files (and other
      stuffs as iptables forwarding rules) in a csync'd directory.
      When the "active" Xen host dies, you can quickly boot up the VMs
      on the other Xen host after switching the DRBD volumes into
      "primary" mode.
      If xen's VMs confs are the same, you'll end up with the same VMs
      with the same IPs (if in a LAN, they immediatly work, othewise you
      have to change the routing in previous-hop)
      
      In this scenario, you can also think to go further (as i did) and
      run a "cross-configuration" with both Xen server running VMs on an
      active DRBD, but holding the passive DRBD of the other server.
      This way you can run half of the VMs on a server and the other
      half on the other server ;) 
      
      Side notes:
      - On a 1Gb/s eth link it works for low global disk write rates.
      10GB fiber/eth link is required for high disk write rates such as
      in storage servers.
      - Be careful to disk write speed: I experienced dramatic slow down
      with Debian 10 when booted Xen kernel (comparison made against
      regular kernel boot)
      
      Hope it helps
      g

On 24/06/21 13:16, mabi wrote:

> Thanks Florian and GD for your answers.
>
> I should have been more precise, I am looking into building a active/passive dual node Xen installation. I don't need active/active as I believe this is also more dangerous.
>
> Also I was thinking that I would manually failover the VM whenever necessary in order not to rely on additional external tools such as corosync/pacemaker and hence avoid more complexity.
>
> So as you notice, at least for a start, I am trying to keep things as simple as possible. If I understand correctly that should be possible with Xen and all I need is multipathd and CLVM, is this correct?
>
> Then regarding CLVM, I checked Debian buster but could not find any CLVM-related pacakges. Is maybe CLVM not available on Debian?
>
> Regards,
> Mabi
>
> ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐
>
> On Thursday, June 24th, 2021 at 12:28 PM, Florian Heigl <florian.heigl@xxxxxxxxx> wrote:
>
> > Hi,
> >
> > you can look into solutions based on cLVM or OCFS2 + Corosync/Pacemaker.
> >
> > Don't forget to set up multipathd so your system can handle the link/controller failovers.
> >
> > This has been done, and also has been/is a commonplace solution. There is also lots of blog posts that you can dig up once you search the right way.
> >
> > I would avoid running natively on SAN luns attached to VMs due the risk of "the cluster stack had an error / was misconfigured". If you'd failover manually that would be less of an issue. The clusters like Pacemaker can protect the VMs a bit using SCSI reservations.
> >
> > There was also Remus for running 2 VMs in lockstep for HA, but that was expecting no shared storage and was never polished by anyone to be worthwhile for production use.
> >
> > A fair warning: Most homegrown HA setups like they're done commonly in the ISP industry tend to blow up much more often than what a proper solution should be like.
> >
> > It might be better to pick something pre-made for that purpose if you don't have the SAN/Cluster experience.
> >
> > I.e. XenServer/XCP or Oracle VM3.
> >
> > Good luck!
> >
> > Florian
> >
> > > Am 24.06.2021 um 10:09 schrieb mabi mabi@xxxxxxxxxxxxx:
> > >
> > > Hello,
> > >
> > > Is it possible with Xen on Debian 10 to have two Xen servers both directly attached in a redundant way through HBA interfaces to a single SAN?
> > >
> > > The goal here would be to achieve higher availability of the Vms in case one Xen server is down for maintenance or because it is defective. This would mean that the the virtual machines can continue to run on the second available Xen server. The SAN would be used to store the virtual machines images directly via LVM I guess.
> > >
> > > I did not find any Xen documentation or third-party howtos in order to do that. Does anyone have any pointers to some documentation or hints? or maybe this is simply not possible?
> > >
> > > Best regards,
> > >
> > > Mabi
> > >         
> >       
>