Hello,
I
tested also Your „second“ possibility
vnc=1
vnclisten='IP_of_my_xen_server
vncdisplay=4
vncunused=1
and
in my case on Xen 3.1.0 the vncdisplay parameter was ignored. So, from my point
of view if You want to specify the port explicitely by setting vncdisplay, it
works only with
vncunused=0
è
exactly like Philippe below wrote...
with regards Artur
From: xen-users-bounces@xxxxxxxxxxxxxxxxxxx
[mailto:xen-users-bounces@xxxxxxxxxxxxxxxxxxx] On Behalf Of Artur
Linhart - Linux communication
Sent: Thursday, September 20, 2007 1:16 PM
To: 'trilok nuwal'
Cc: 'Philippe Vanhaesendonck'; 'Dylan Martin'; 'Scott Serr'; 'Alessandro
R.'; xen-users@xxxxxxxxxxxxxxxxxxx
Subject: RE: [Xen-users] VNC to HVM not starting
Hello,
I could not test all the combinations, but I think You are right. And if the
vncunused parameter is omitted, then also vncdisplay parameter is ignored even
if specified - like already wrote Philippe...
With regards, Archie
From: trilok nuwal [mailto:tc.nuwal@xxxxxxxxx]
Sent: Thursday, September 20, 2007 12:34 PM
To: Artur Linhart - Linux communication
Cc: Philippe Vanhaesendonck; Dylan Martin; Scott Serr; Alessandro R.;
xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] VNC to HVM not starting
From my experience :
when
vnc=1
vnclisten='IP_of_my_xen_server
vncdisplay=4
vncunused=0
Always allocate the port 5900 (standard VNC) + 4 (vncdisplay) = 5904 for the
display. If it is used by soem other application this will just hang.
vnc=1
vnclisten='IP_of_my_xen_server
vncdisplay=4
vncunused=1
allocate the port 5900 (standard VNC) + 4 (vncdisplay) = 5904 for the display
if it is free else allocate other free port.
vnc=1
vnclisten='IP_of_my_xen_server
vncunused=1/0
allocate free port.
Please correct me if my
understanding is wrong.
Thanks,
Trilok
On
9/20/07, Artur Linhart - Linux communication <AL.LINUX@xxxxxxxxxxx> wrote:
Hello,
Yes, thank You very much, it is
it :-)
So, for me the following
configuration
vnc=1
vnclisten='IP_of_my_xen_server' # Here place IP of the Xen server
vncdisplay=4
vncunused=0
causes the Xen server listens
on the given IP on the port
5900 (standard VNC) + 4 (vncdisplay) = 5904
And I can vonnect to it through the VNC viewer!
:-)
The "display" value seems to be valid at least also for the number 21
and
port 5921 (I do not know if there is some max display number)
Dylan, I propose to place such an example into the FAQ You are creating,
sure, if it is not already there ;-)
With best regards
Artur
-----Original Message-----
From: Philippe Vanhaesendonck [mailto:xen@xxxxxxxxxxx]
Sent: Wednesday, September 19, 2007 11:21 PM
To: Artur Linhart - Linux communication
Cc: 'Scott Serr'; 'Alessandro R.'; xen-users@xxxxxxxxxxxxxxxxxxx
Subject: Re: [Xen-users] VNC to HVM not starting
Be aware that tere seems to be some precedence in the parameters.
If my memory serves well, you must set vncunused to 0 if you want
vncdisplay to be considered.
/P.
Artur Linhart - Linux communication wrote:
> Hello,
>
> I've tested it and this is not true what
I said and thought, it
> seems to be the fact the display is not influencing the port...
>
> What does it influence, dies anybody
know it? Is it a "bug or a
> feature"? What is then the purpose of the vncdisplay option in the
> configuration?
>
__________ Informace od NOD32 2541 (20070920) __________
Tato zprava byla proverena antivirovym systemem NOD32.
http://www.nod32.cz
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users
__________ Informace od NOD32 2541 (20070920) __________
Tato zprava byla proverena antivirovym systemem NOD32.
http://www.nod32.cz
